GFI System
GFI System Webpage
  • Home
  • Pedals
    • Synesthesia >
      • SymmLab
      • Sound Clips
      • F.A.Q
      • Documentation
    • Specular Tempus >
      • SpecLab
      • F.A.Q
      • Algorithms
    • Triple Switch
    • Jonassus Drive
    • Specular Reverb V3
    • Clockwork Delay V3
    • Cabzeus >
      • CabsLab
      • F.A.Q
    • Cabzeus MONO
    • ( phased-out pedals ) >
      • Specular Reverb V2
      • Clockwork Delay V2
  • Artists
  • PURCHASE
    • GFI Store
    • Worldwide Dealers
    • Local Dealers
    • Becoming our Dealer
  • Downloads
  • Info
    • About Us
    • Contact
  • Home
  • Pedals
    • Synesthesia >
      • SymmLab
      • Sound Clips
      • F.A.Q
      • Documentation
    • Specular Tempus >
      • SpecLab
      • F.A.Q
      • Algorithms
    • Triple Switch
    • Jonassus Drive
    • Specular Reverb V3
    • Clockwork Delay V3
    • Cabzeus >
      • CabsLab
      • F.A.Q
    • Cabzeus MONO
    • ( phased-out pedals ) >
      • Specular Reverb V2
      • Clockwork Delay V2
  • Artists
  • PURCHASE
    • GFI Store
    • Worldwide Dealers
    • Local Dealers
    • Becoming our Dealer
  • Downloads
  • Info
    • About Us
    • Contact

Cabzeus Downloads

CABZEUS

Firmware
( v2.2 - build 0 )
Cabzeus Firmware v2.2.fdt
File Size: 6 kb
File Type: fdt
Download File

Firmware Update procedure :
* This update procedure requires a factory reset which will erase the presets stored in your pedal. To avoid losing your presets you can first save your presets as 'Local Preset' in your computer and later restore it back to your pedal. Do that before you perform the update steps below.

1.  Download and install editor software CabsLab 2.0.0 (or higher).

2.  Download firmware v.2.2
       Mac : don't use the Safari browser, use Chrome or Firefox instead. 
       Windows : do not use the Edge or Internet Explorer browser, use Chrome of Firefox instead.


3.  Do Firmware Update :
     -  Hold down the preset selector knob on power up. Release when both LED 1 and 4 light up.
     -  Connect the pedal to your computer and start CabsLab.
     -  When prompted, browse for the firmware file you've just downloaded and start the update
.

4.  Do Factory Reset
     -  Menu >> Factory Reset.
        (If you encountered errors at this step, reboot the pedal and try again).

5.  Reboot the pedal - DONE.

Software
( Windows )
CabsLab 2.0.6 Installer (Win).zip
File Size: 12344 kb
File Type: zip
Download File

USB Driver Setup (Win).zip
File Size: 2071 kb
File Type: zip
Download File

* USB driver need to be installed only once. This is the same driver used by SymmLab and SpecLab.
( Mac OS X )
CabsLab 2.0.7 Installer (Mac).zip
File Size: 5349 kb
File Type: zip
Download File

(!) Please read the Installation Guide (included in the zip file) first before installing.
OS Compatibility
  • Windows : XP, 7, 8.x, 10
  • Mac : 10.15 (Catalina), 10.14 (Mojave), 10.13 (High Sierra), 10.12 (Sierra), 10.11 (El Capistan), 10.10 (Yosemite), 10.9 (Maverick).

Documentation

User Manual - v2.0.pdf
File Size: 6327 kb
File Type: pdf
Download File

© COPYRIGHT 2016. GFI System All rights reserved