GFI System
GFI System Webpage
  • Home
  • Pedals
    • Synesthesia >
      • SymmLab
      • Sound Clips
      • F.A.Q
      • Documentation
    • Specular Tempus >
      • SpecLab
      • F.A.Q
      • Algorithms
    • Triple Switch
    • Jonassus Drive
    • Specular Reverb V3
    • Clockwork Delay V3
    • Cabzeus >
      • CabsLab
      • F.A.Q
    • Cabzeus MONO
    • ( phased-out pedals ) >
      • Specular Reverb V2
      • Clockwork Delay V2
  • Artists
  • PURCHASE
    • GFI Store
    • Worldwide Dealers
    • Local Dealers
    • Becoming our Dealer
  • Downloads
  • Info
    • About Us
    • Contact
  • Home
  • Pedals
    • Synesthesia >
      • SymmLab
      • Sound Clips
      • F.A.Q
      • Documentation
    • Specular Tempus >
      • SpecLab
      • F.A.Q
      • Algorithms
    • Triple Switch
    • Jonassus Drive
    • Specular Reverb V3
    • Clockwork Delay V3
    • Cabzeus >
      • CabsLab
      • F.A.Q
    • Cabzeus MONO
    • ( phased-out pedals ) >
      • Specular Reverb V2
      • Clockwork Delay V2
  • Artists
  • PURCHASE
    • GFI Store
    • Worldwide Dealers
    • Local Dealers
    • Becoming our Dealer
  • Downloads
  • Info
    • About Us
    • Contact

​S Y N E S T H E S I A
​

F.A.Q

​Frequently Asked Questions on Synesthesia


Q : So only 3 parameters per algorithm?
A  : There are 3 primary parameters, adjusted by turning the Speed, Depth, and Tweak knobs, then there are 3 secondary parameters, adjusted by turning the same Speed, Depth, and Tweak knobs while holding down the button. Note that each knob is also a button.

Q : Is it possible to quickly swap the X and Y settings? Say I have a phaser on X going into a chorus on Y, I want to know how it would sound if I have chorus going into the phaser instead.
A  :
Absolutely, we have included the XY Swap function to accomplish exactly that :
  • Tap the X and Y button simultaneously. Do it again to swap back to original setting.

Q : Can I do tap-tempo on the pedal itself without using external tap tempo pedal?
A  : 
Yes you can. There is an option to configure footswitch B/X as a preset button or as a tap-tempo button :
  • Global  >>  Footswitch B/X  >  Tap Tempo​​

Q : Can Synesthesia receive MIDI Clock signal?
A  :
Certainly.


Q : Do you have a table that list of all the algorithms and their parameters?
A  :
Sure, here it is.
Picture
Q : I plugged in an expression pedal but nothing happened when I rock the pedal.
A  : 
Make sure you have the expression pedal plugged in to the A.C.E jack before powering up Synesthesia. If you plug the expression pedal in when Synesthesia is already powered up it will not get recognized. Also, you must map at least one parameter knob to the expression. Consult the user manual or our tutorial videos for information on how to map a parameter knob to the expression pedal.


Q : Will any expression pedal work?
A  : 
The most important thing to watch for is the wiring polarity, the potentiometer's wiper must be connected to the Tip terminal of the jack. Some expression pedal has it's wiper connected to the Ring terminal instead, this will not work.
Picture
Expression pedal with 10Kohm potentiometer value will work best.
Q : I'm not getting any signal on the Left output, only the Right output is working.
A  :
Check the tiny switch below the USB and power jack (top side), it may have been inadvertently set it to Pre/Post position. 
© COPYRIGHT 2016. GFI System All rights reserved