CabsLab is a piece of software written exclusively to work with Cabzeus pedal. You have full access to complete simulation parameters that you can adjust and play around with, while auditioning the resulting change in sound with your pedal, in real time. When you've found your favorite settings you can store them as presets in Cabzeus.
Usage :
Highlights :
Usage :
- Customize the speaker simulation system algorithms.
- Store the customized algorithms to your pedal as presets.
- Read the stored algorithms in your pedal and display them on screen.
- Save local presets (favorites) in your computer.
- Configure the MIDI channel on your pedal.
- Revert your pedal to factory setting.
- Update your pedal’s firmware.
Highlights :
- Real-time preview as you tweak the parameter controls.
- ‘Solo’ function for single speaker auditioning or quick A/B comparison.
- Extensive set of speakers simulation system parameters.
Stereo Cabs mode panel
|
Stereo Mics mode panel
|
Software ( current version : V2.0.6 - works with Firmware V2.0 )
|
Windows : XP, 7, 8.x, 10
* USB Driver need to be installed only once. When installing a newer software version the USB driver need not be re-installed. |
| ||||
|
Mac OS X : 10.14 (Mojave)
10.13 (High Sierra) / 10.12 (Sierra) 10.11 (El Capistan) 10.10 (Yosemite) 10.9 (Maverick). Compatibility with older / newer versions has not been verified. |
(!) Please read the Installation Guide (included in the zip file) first before installing.
| ||
* Please uninstall older software version from you PC or Mac first before installing newer version.
Firmware ( current version : V2.0 (build 3) - requires CabsLab v2.0.0 or above )
| Cabzeus Firmware v2.0.fdt |
Release notes : Firmware v2.0 features the following enhancements :
- The two on-board 'Mic Position' knobs can now be reassigned to control other parameters.
- Title can now be given to presets.
- 'Short delay' feature is expanded to be able to function as 'stereo-enhancer', as a 'frequency notch generator', or as 'doubler'.
- Speaker library and Tone Chart interface in CabsLab is vastly enhanced for ease of navigation
Update procedure :
* This update procedure requires a factory reset which will erase the presets stored in your pedal. To avoid losing your presets you can first save your presets as 'Local Preset' in your computer and later restore it back to your pedal. Do that before you perform the update steps below.
1. Download and install editor software CabsLab 2.0.0 or above.
2. Download firmware v.2.0
3. Do Firmware Update :
- Hold down the preset selector knob on power up. Release when both LED 1 and 4 light up.
- Connect the pedal to your computer and start CabsLab 2.0.0.
- When prompted, browse for the firmware file you've just downloaded and start the update.
4. Do Factory Reset
- Menu >> Factory Reset.
(If you encountered errors at this step, reboot the pedal and try again).
5. Reboot the pedal - DONE.
* This update procedure requires a factory reset which will erase the presets stored in your pedal. To avoid losing your presets you can first save your presets as 'Local Preset' in your computer and later restore it back to your pedal. Do that before you perform the update steps below.
1. Download and install editor software CabsLab 2.0.0 or above.
2. Download firmware v.2.0
3. Do Firmware Update :
- Hold down the preset selector knob on power up. Release when both LED 1 and 4 light up.
- Connect the pedal to your computer and start CabsLab 2.0.0.
- When prompted, browse for the firmware file you've just downloaded and start the update.
4. Do Factory Reset
- Menu >> Factory Reset.
(If you encountered errors at this step, reboot the pedal and try again).
5. Reboot the pedal - DONE.